PSM 200 Personal Monitor System

 

PSM200

PSM 200 Personal Monitor System

The entry to professional in ear personal monitoring from Shure. This package contains SE112 Sound Isolating Earphones, a P2R Bodypack Receiver and a P2T TransMixer.

Why is in ear monitoring more effective than using a wedge speaker on stage?

Using a Shure monitoring system allows you to hear the music via your earphones at the exact time it is played. There can be a short delay in music coming out of the wedge, which can cause performers to play out of time. Wedge monitors will sound fine when standing in one position, but if you move to the left or right, that sound is likely to change. With in ear personal monitoring, the sound will be constant and comes with you, wherever you go. Using wedge monitors long term can also be damaging to your ears. Using Shure sound isolating earphones cuts out the sound around you leaving you to focus on playing in time.

How do I set up my PSM 200 in ear system?

Simply connect two line-level or mic–level inputs directly into the transmixer. Set the frequency on the transmixer using a single button, and the same again on the bodypack receiver. Connect your earphones to the P2R, set up your desired mix using the personal mix controls on the front of the transmixer and you are now all ready to go.

Features
  • Built-in audio limiter
  • Front mounted antenna
  • Two mic/line input channels for mix control
  • Built in headphone limiter
  • Volume control on bodypack receiver
  • 1/2 Rack space

  • Technical Data

    Wired Bodypack Option Yes
    PSM 200 System
    RF Carrier Frequency Range 518¬-865 MHz (country dependent)
    Modulation FM +/- 35 kHz Deviation (Nominal)
    Operating Temperature -7 degrees C to +49 degrees C (+20 degrees F to +120 degrees F) 
    P2T TransMixer
    Modulation Limiter Internal peak limiter (>10:1 hard knee compression)
    Antenna 1/4 Wavelength, semi-rigid, PCB Mount
    Connector Type XLR/1/4-inch combo
    Nominal Input Level -25 dBu @ 1/2 volume (12 o'clock)
    Maximum Input Level -5 dBu @ 1/2 volume (12 o'clock)
    Current 170 mA maximum
    Dimensions 220 mm x 140 mm x 40 mm (8.6 in. x 5.6 in. x 1.7 in.)
    Net Weight 370 g (13 oz.) 
    Audio Input
    Connector Type XLR/1/4-inch combo
    Configuration electronically balanced
    Actual Impedance 1 kΩ
    Nominal Input Level -25 dBu @ 1/2 volume (12 o'clock)
    Maximum Input Level -5 dBu @ 1/2 volume (12 o'clock)
    Pin Assignments XLR: 2=hot; 3=cold, 1=ground
    1/4: Tip=hot, Ring=cold, Sleeve=ground
    Phantom Power Protection Yes:Up to 52 Vdc
    Audio Output
    Connector Type XLR
    Configuration Electronically balanced
    Pin Assignments 2 = hot ; 3 = cold, 1 = ground
    Phantom Power Protection Yes: Up to 52 Vdc
    P2R Bodypack Receiver
    RF Sensitivity 109 dBm typical
    Squelch Threshold 102 dBm typical
    Antenna Attached Whip
    Audio Input Connector Connector Type: 1/4-inch Mono
    Impedance 1 MΩ
    Maximum Input Level LO = +0 dBu; HI = 10 dBu
    Frequency Response 30 Hz to 20 kHz (+/ 3 dB); earphone dependent
    Power Requirements 9 V alkaline battery, Duracell® type MN1604 recommended
    Battery Life (Volume Dependent) 6 hrs (Wired) ; 4 hrs (Wireless)
    Audio Output Connector 1/8 inch (3.5 mm)
    Minimum Load Impedance 8 Ω
    Net Weight 100 g (3.52 oz.), less battery
    Overall Dimensions 122 mm x 73 mm x 32 mm (4.809 in. x 2.875 in. x 1.251 in.)
    SE112 Sound Isolating™ Earphones
    • Dynamic MicroDriver for great sound with deep bass and impressive sound isolation.
    • Fixed cables.

  • Downloads

    PDF Personal Monitoring System Quick Guide
    English
    PDF PSM200 User Guide
    English